Configuring your Windows 10 PC to sleep is an excellent way to save energy. It makes sure you can resume without any waste of power. However, it happens that your PC goes to sleep mode automatically or keep waking you up. There may be many factors responsible for this, so it is difficult to diagnose the exact one.
How to prevent Windows 10 from going to sleep mode?
Generally, sleep mode is used when you wish to step away from your PC for a few minutes and let the system enter a lower power state. Once you come back, all you need to do is press a button to resume working. It is annoying if your Windows 10 frequently enter sleep mode. This is because it would waste your time often bringing it back to normal working mode. Let’s look at the different methods to avoid Windows 10 from entering into sleep mode:
Method-1: Sleep Mode Settings
The first approach you can adopt is to check your sleep mode settings. Once your Windows 10 PC enters sleep, you can check all your settings as well as factors that prevent a sleep state. Typically, the power options, the hardware, and configuration can influence the way power and sleep buttons function. In case your PC has already been installed with updates, or if there is an installed app that demands a restart, then your PC might not sleep at all.
In case you are working on a shared computer or a Windows 10 PC that is not yours, there is a possibility that somebody else might have twisted the power options. To access sleep mode settings, follow the below steps:
Step-1: Navigate to ‘Control Panel’ and select
‘Power Options.’ Now click on ‘Choose when to turn off the display.’
Step-2: At the right side of the ‘Put the computer to sleep,’ you need to check out the values and ascertain that they are set properly. In case your PC is about to roll into sleep mode too soon, or taking much time to go sleep, this step needs to be followed without fail.
Note: If the current power plan is set to Balanced, then several devices are permitted to enter a low power state. It can occasionally pose problems. If you have disabled Sleep and still find issues on Balanced, then you need to change it to High performance. For that, you may consume a bit more power, but devices that may be causing a problem are usually instructed to stay on.
Method-2: Disable Fast Startup:
The Windows 10 Fast Startup feature is basically a setting that assists your PC startup quickly after shutdown. This feature does that by saving an image of the kernel as well as loaded drivers to the C:hiberfil.sys after shutdown. Once you have shut down and then restarted your PC, Windows 10 would load the hibernation file inside the memory in order to resume your PC.
Follow the below steps to disable fast startup:
Step-1: Open Control Panel
and then navigate to
Power Options. Now click on ‘Choose what the power buttons do.’
Step-2: In this step, you need to click on ‘Change settings that are currently unavailable’ and then uncheck ‘Turn on Fast Startup’ to disable this setting.
Method-3: From the Settings App:
Open the Settings app from the below link:
- Step-1: Now press the Start button located in the lower-left corner of your screen, and then you have to choose the ‘Settings’ gear.
- Step-2: Navigate to ‘System.’ It is the first category located on the left side of the app.
- Step-3: Now open the ‘Power settings.’ Choose the “Power and sleep” located from the left pane.
- Step-4: Go to Sleep settings present under the ‘Sleep’ header that is located under the power settings.
- Step-5: You have to disable ‘sleep.’ Now you must tick both the dropdowns present under ‘Sleep’ to Never.
Method-4: From the Control Panel:
- Step-1: Firstly, launch the Windows 10 shortcuts key Win+X to navigate the Control Panel and then open it.
- Step-2: Navigate the Power Options and click on it.
- Step-3: In this step, you have to click the link ‘Choose when to turn off the display’ located under the left pane of your window screen.
- Step-4: Now, you have to choose the link ‘Put the computer to sleep’ option. Here, you can set the duration from the dropdown menus according to your requirements.
Setting the duration is helpful for Plugged in and On Battery. Finally, make sure you save the changes before shutting down the window.
Method-5: From the Windows Power Options:
Step-1: First, navigate to ‘Control Panel>Appearance and Personalization>Personalization>Change Screen Saver.’
Step-2: A window will pop up with the name ‘Screen saver Settings.’ Now uncheck the box beside ‘On Resume, Display Logon Screen.’
Note: The problem that may occur now is the settings that you store or change applies permanently. If you wish that your system goes for sleep at a specific time, then it would not occur due to these settings. To resolve this issue, you can try the below method that uses third-party tools.
Method-6: Using Third-Party Tools:
The below section will familiarize you with different third-party tools that you can try out to prevent Windows 10 from entering sleep mode.
i. Don’t Sleep
You can download Don’t Sleep from below link:
This third-party tool is a portable tool that prevents your system from the shutdown, restart, sleep, or hibernate. The key benefit of this tool is that it can offer you a Timer that assists you in let your settings changeable. In case you wish to wake up your system for definite hours, simply add that particular time limit in timer and start the timer. This tool would save your time by not frequently touching your system so that it prevents you from going to sleep mode.
You can download Insomnia from below link:
Insomnia is available for both 32 Bit as well as 64 Bit Windows. This tool is quite small and straightforward to use. When installed, a small window would show up on your screen. This window indicates that the computer could not roll into sleep when this window is open. Till the time this window is open, your Windows 10 PC will stay awake and would not go to sleep. Therefore, there is no need to set any timer or anything about settings to make our system awake. The Insomnia tool is easy to use. Simply allow the window to open.
You can download Noise from below link:
Noise is a simple-to-use third-party tool. Once you have installed it, a new window will pop up that inquires you to enter any key from your keyboard. Subsequently, after every 60 seconds, it submits the keystroke to the processor. Therefore, the processor assumes that somebody is using and pressing the keys. Thus, your Windows 10 system will be prevented from going to sleep, and the screen will stay awake. By opening this window, the user can easily use any functionality. Using this window will not create any hassles or prevent users from his/her work.
This third-party tool is made available in your system tray. It is easy to open it by clicking its icon and then entering any key. Also, you can add combinations of Character key and a Number key.
The discussed methods are practical and easy to use for preventing your Windows 10 system from going to sleep. Now there would be no hassles of frequently turning on the screen and letting it resume from sleep mode.