How to Fix the Automatic Repair Loop in Windows 10

Are you wondering how to fix the automatic repair loop in Windows 10? You have landed in the right place.

The Automatic Repair is a unique and thoughtful feature offered on Windows 10. It lets Windows users take up the repair tasks on their computers in an automatic manner. However, there are situations where you would find that the issue remains unresolved and your computer is not repaired correctly. It can even cause a job in some cases where your computer remains on a single screen for a prolonged period and experiences a Windows 10 automatic repair loop.

How to fix this issue? Several options can be helpful enough in resolving the problem and get your system back into place.

What is the Automatic Repair Loop?

The Automatic Repair Loop is a unique issue that can result because of multiple reasons. Instead of repairing your computer, the tool will begin looping through the same screen over and again. The automatic repair tool is a great choice and can assist you in more ways than repairing and resolving the issues on its own.

However, the tool can malfunction at times and can result in unwanted loops. This can happen due to multiple reasons. Some of them can be

The issues with the Windows System registry.
The bootmgr file on your system may have been corrupted. This is the file that controls the Windows boot process explicitly.
Corrupted, missing, or damaged system files
The issues with your hardware drivers.

Apart from those specified above, there may be a few unknown reasons that can cause your system to malfunction.

How to Fix the Automatic Repair Loop in Windows 10?

The solutions will depend on the exact reasons that could be causing the issue on your computer. Now that you may not be able to arrive at the precise cause that can be at the root of the automatic repair loop on your system, it would be essential to try out as many solutions as possible and check out if they help you resolve them.

Fix 1 – Configure Hard Drive as the first boot drive

In case your PC is booting from the secondary drive, and it has issues on it, you may end up with it affecting you and causing problems on your system. Configuring your hard drive as the first boot drive can be an excellent option.

Launch your BIOS settings and change the preferences. You can do that by tapping on the F12 key when your PC is booting up. Reboot your computer, and that should ideally resolve the issue for you.

Fix 2 – Disable Automatic Repair

The Automatic Repair Tool itself may be a reason for the loop issue. Disabling it can be one of the excellent options for resolving the Automatic Repair loop in Windows 10.

Here is how you would do it –

Insert your Windows installation disk into your system.
Start your computer and boot from your DVD
In the Windows menu that appears, choose to Troubleshoot -> Advanced Options.
Reach up to Command Prompt and enter the following command

bcdedit /set {default} recovery enabled No

Exit the command prompt and restart your computer. The issue should be resolved in most cases.

Fix 3 – Restore your Windows Registry

One of the reasons you would find your computer facing the issue can be the corrupted or damaged Windows Registry. Restoring the Windows Registry can help you achieve the best results.

Here is how you can achieve the task –

From the Windows Boot Options, choose to Troubleshoot -> Advanced Options.
Choose Command Prompt, and type in the following command

copy c:windowssystem32configRegBack* c:windowssystem32config

It may ask you to rewrite a few files if needed. Confirm the same. Your Windows Registry will now be restored with a backed-up version.

Check if it resolves the issue in your case.

Fix 4 – Rebuild Boot Configuration Data or BCD

Rebuilding BCD can help you achieve the best results in resolving the automatic repair loop issue. The master boot record can thus be helpful enough in making the right solution.

Follow the steps as in the following discussion –

Reach up to the Command Prompt following the steps indicated in the previous fixes.
Type in the commands here below –

bootrec.exe /rebuildbcd

bootrec.exe /fixmbr

bootrec.exe /fixboot

Make sure you press ENTER after each of those commands.

The above commands will repair the Master Boot Record and Boot Configuration Data on your system. Check if this resolves the issue in your case.

Fix 5 – Remove the File that has created the problem

Use the boot menu and reach up to the Command Prompt and follow the next steps from here below –

On the Command Prompt, type in the following command and press Enter –

C:cd WindowsSystem32LogFilesSrtSrtTrail.txt

If any of the files are corrupted, you should get the name of the file in the command prompt result
Delete the file by using the command

Del <filename>

Check if the Automatic Repair loop is resolved.

Fix 6 – Use System File Checker

The Automatic repair loop can also be caused if any of your system files are damaged or corrupted. Running the System File Checker can help you resolve the issue.

You can follow the steps here for resolving the problem –

Go to Command Prompt using the above method.
Type in the following command and press ENTER

SFC /scannow

Wait till the system checks your files and corrects any of the data that may have errors. Once the scan is completed, check if the issue is resolved for you.

The Closing Remarks

Those were a few options that should help you get rid of the Automatic Repair Loop. Resolving the issues may not come easy enough. In case your PC keeps restarting, accessing the Advanced options may not be much easy. The only way you would be able to access it is to use a Windows installation DVD or a flash drive for the purpose.

Check which of the solutions above resolve the problem in your case. Share which of the options did help you determine the issue.